Your present position: Technology >> PVC Anti-static floor construction program

Construction requirements：

→ Requirements on the ground
    On the ground can be the basis for the terrazzo floor, porcelain floor tiles, wood floor, 1: 3 cement mortar on the ground. Request the formation of the ground, dry (cement surface of the ground should be white), no uneven surface roughness should be less than 2 / 1000mm. On the ground must have the strength, not from sand, shell phenomenon. On the ground to be dry, freshly ground dry normally takes 30 days.

→ Construction materials and tools
※Construction materials
    Floor: anti-static Permanent PVC plastic on the floor.
    Specifications are: 300x 300 mm 600x600 mm;
    Conductive plastic: PVC plastic anti-static floor professional at the end of conductive plastic;
    Copper foil (or aluminum foil) 0.03 -0.10 mm thickness of the width of 20-30 mm;
    Alcohol: industrial;

※Construction tools
    Scraper: for the conductive plastic coating; Rubber hammer: for the hammering of plastic on the floor to the ground with the full and sticky;
    Zhaoou: voltage 500V, used to measure the conductivity;
    Copper electrode: specifications for Φ 50mm, weighs 0.5kg, the number two, for supporting the use of Zhaoou table;
    Blade: for cutting plastic floors; Electrode: Φ 3.5-4.0mm; torch :800-1000W;
I circle Blade: elimination of outstanding welding rod.

Construction procedure：
    Cleaning the ground - line - conductive plastic coating - Shop grounding grid guide - leads to earth - Putie floor - welding cracks on the floor - on the surface clean

Construction methods and procedures
※Clean the ground to find the center line.
    First of all, floating ash on the ground will be cleared, and then measuring the room to find out the location of the center line, painted center lines cross, Cross asked sub-vertical line;

※On the ground at the end of uniform coating layer of conductive plastic binders, dry place to be;

※The laying of copper foil (or aluminum foil) Network
    Until the end adhesive glue non-stick in hand, on the ground in accordance with the provisions of the paste-size copper foil (or aluminum foil), to form networks, the width of 3 m square. Aluminum foil attached). Attention of the copper foil (foil) Cross, to ensure that the copper foil (foil) turn-on;
    Zhaoou measuring adjacent table with copper foil (foil) between the resistance and its resistance to be <1.0x10 5 Ω, if there is need to find out the cause of sense to re-paste to ensure that the network at any point on Earth are the turn-on ;
    Paste a good foil (foil) network in every 100 square meters, at least four plants and ground wire connected to the system.

※Laying on the floor
    To be on the ground floor and the adhesive on the back of the hand may touch the non-sticky sticky start laying on the floor. From the center of the distance between adjacent begin dimensions for the floor, lay at the location from the beginning of block-by-four to start For welding, each floor for the gap between 2-3mm, paste side by side rubber hammer hit the floor in order to ensure inter-stick A solid balance until the completion of construction of the entire room;
    The construction process, with regular testing Zhaoou table on the floor of the copper foil (foil) between the resistance check-on and, if different, it is necessary to find out the reason for re-paste in order to ensure that each of the ground floor of the resistance in the 10 5 -10 9 Ω between.

※Welding：
    800-1000W use of plastic welding torch along the welding gap between the floor in the past, they should pay attention to welding can not be missed welding, Xu Han, and welding rod to shovel to the face plate with the same formation, and then the surface must be clean, dealing with lighting.

※Construction quality requirements
    The floor surface resistance value should be 10 5 -10 9 Ω;
    Fengzhong the welding electrode no obvious uneven;
    No bubbles on the surface, the shell-free phenomenon; no significant construction pollution;
    Floor joints between adjacent dislocation should not be larger than 2mm, welding seam between the floor adjacent to no obvious gap.